Releases

About this release

This Temetra Analysis release is automatically applied for hosted Software as a Service (SaaS) customers on the release date. For managed appliance customers, Temetra Analysis releases are managed by Itron and may use a different schedule.

Resolved issues

This section lists significant issues that have been addressed in this Temetra Analysis release.

3436687: Incorrect NRW values

In Operational Visibility, non-revenue water (NRW) values displayed incorrect percentages. This issue has been resolved. The following calculations apply to total loss and NRW values:

• Total Loss = (supplied volume) - (metered consumption)

• Total Losses (split) = (real losses) + (apparent losses)

• NRW = (total losses) / (supplied volume) * 100

NRW values are limited so that maximum NRW does not exceed +/-100%.

About this release

This Temetra Analysis release is automatically applied for hosted Software as a Service (SaaS) customers on the release date. For managed appliance customers, Temetra Analysis releases are managed by Itron and may use a different schedule.

Enhancements

This section lists new or updated functionality included in this Temetra Analysis release.

3145389: Support for mixed DMA read frequencies (monthly, daily, hourly)

In Operational Visibility, DMAs now support the following meter-reading combinations:

• Daily + hourly

• Daily + monthly

• Monthly + daily + hourly

• Monthly + hourly

This allows for water balance calculations to be performed for customers with mixed frequency data sets (for example, hourly, daily, and monthly interval data). Previously, a DMA needed to have the same frequency of interval data for all service points contained within the DMA. This makes the solution more flexible for customers who are in the process of migrating from manual/drive-by meter readings to AMI.

3326193: Sector status card enhancement

Improvements to the dashboard Sector Status card have been made to improve readability.

3339324: Added water quality station details

In Transmission Mains Monitoring, a panel displaying details for Water Quality Monitoring Stations appears on the Sector Entity page if there are any water quality stations associated with that sector.

3339356: Pump station import enhancement

The pump station configuration import functionality has been updated to allow one or more flow sensors and pressure sensors to be assigned to a pump station. The update also allows a formula to be assigned to a pump station to calculate KPIs related to pump station efficiency.

3339372: Pump station data chart

Transmission Mains Monitoring now features a chart for visualizing pump station data. Users can create a pump station and assign flow sensors, pressure sensors, and energy sensors to the pump station. Formulas can be created to calculate KPIs related to the efficiency of the pump stations. Users can select the pump station to navigate to the pump station entity page, where they can view the raw data and KPIs associated with the pump station.

3339387: Added support for monitoring pumps and pump stations

Transmission Mains Monitoring now supports monitoring pumps and pump stations. Users can select a pump station icon on the Transmission Mains Monitoring map or table to navigate to the entity screen for that pump station to view underlying data and details.

3340434: Added sensor type icons

Transmission Mains Monitoring now features map icons for the following sensor types:

• Flow sensor (Q) - [ l/s, l/h, l/m, gal (US)/s, gal (US)/m, gal (US)/h ]

• Water level sensor (H) - [ m ]

• Pressure sensor (P) - [ bar, mH2o ]

• Index based volumetric sensor (I) - [ m3 ]

• Volumetric sensor (V) - [ m3 ]

• Energy sensor (E) - [ kWh ]

• Current sensor (A) - [ A ]

• PowerFactor sensor (PF) - [ N/A ]

• PumpSpeed sensor (N) - [ rpm ]

• Power Sensor (POW) - [ w, hp(e) ]

3351974: Detect Endpoints with No Reads support for meter replacement

The Detect Endpoints with No Reads report in Event Investigation now handles endpoint replacements to ensure that the event remains open until a new reading is received for the new endpoint following a meter replacement. The LastReadDate contains the reading date from the historical meter prior to the replacement. The Detect Endpoints with No Reads event closes when a new reading comes into the system for the new meter associated with the service point.

3362835: User interface enhancements

User experience improvements have been implemented across various areas of the application:

• Dashboard cards for Real Loss (RL) and Apparent Loss (AL) now show DMAs in descending order instead of ascending order.

• The List of Region table columns are now shown in a default order based on usefulness instead of ascending order. For example, Water Supplied and Metered Consumption should appear first.

• The List of DMAs table in list view now includes three links on each DMA row: Entity (water droplet icon), DMA ID, and Description.

3394707: Support for power sensor data

Power sensor data support has been added to allow for the monitoring of power usage of a given distribution asset, such as a pump.

3421988: Column headers to indicate monthly or daily data

In Operational Visibility, text has been added to table column headers to describe whether a column depicts monthly or daily data.

Resolved issues

This section lists significant issues that have been addressed in this Temetra Analysis release.

3347073: EntityPolygon configuration file issue

An issue affecting the import of polygon configuration files for Region entities has been resolved.

3350424: Customer leakage score issue

In Event Investigation, high customer leakage scores were being calculated for service points that did not have associated readings. This issue has been resolved.

3317070: Missing endpoint readings in user interface

Readings for some service points displayed incorrectly in Temetra Analysis, even though the data for those readings existed in the database. This issue has been resolved.

3374023: DMA meter count mismatch

A mismatch occurred between the number of service points being reported in Operational Visibility and the number of service points being reported in Event Investigation. This issue has been resolved. Changes resulting from adding, removing, or reassigning a service point for a DMA are now accurately reflected in both Operational Visibility and Event Investigation.

3392166: Tooltip placement and transparency on graphs

Tooltip information bubbles on graphs obstructed the view of chart data. This has been addressed by adjustments to the position and transparency of tooltips shown on hover so that the user can see underlying graphical data while mousing over a particular point on the chart.

3401780: Calculation jobs remaining in progress over time

Some calculation jobs were observed remaining in an in-progress state for prolonged periods of time. This issue has been resolved. Calculation jobs that have not completed or are partially completed after a 24-hour period are now automatically aborted and given a status of Failed. This update allows users and Itron Support to diagnose any issues with calculations.

3422025/3441732: Calculation jobs failed

Some calculation jobs failed due to an internal system timeout and other technical issues. This issue has been resolved.

3436694: N/A value shown for losses

Water loss calculation jobs resulted in a displayed value of N/A in water balance tables. This issue has been resolved.

About this release

This Temetra Analysis release is automatically applied for hosted Software as a Service (SaaS) customers on the release date. For managed appliance customers, Temetra Analysis releases are managed by Itron and may use a different schedule.

Enhancements

This section lists new or updated functionality included in this Temetra Analysis release.

3142051: Improved performance for device aggregation job

The performance of KPI calculations of service points, sensors, and transmission mains monitoring has been improved to enable near real-time calculation of KPIs up to the last completed hour.

3190735: Improved error reporting for imports

Error reporting for data import jobs has been improved to provide users with better information regarding the reason for the failure of a data import.

3238266: Added transmission mains sectors map

Transmission Mains Monitoring now supports the visualization of water transmission mains and associated assets on a map. For more information, see Sectors map.

3243334: Support for polylines in Import file

The entityPolygon.csv import now supports polylines in addition to polygons to allow for the visualization of linear infrastructure such as water distribution pipes alongside polygonal areas.

3271727: Support for single reading per device in import file

Temetra Analysis is now able to calculate a meter's consumption by comparing the last index stored in the system with that of the next index present in the import file to support water balance calculations for customers with low-frequency data.

3292287: Color coding on sectors map

The Sectors map in Transmission Mains Monitoring features color-coded visualizations of Total Loss % by sector (see also enhancement 3238266). For more information, see Sectors map.

3243347: Added support for Water Quality Station import

Temetra Analysis now supports the import of the WaterQualityStation.csv file to configure water quality stations. A water quality station can be linked to a sector and may contain multiple sensors. With this import, users can define various characteristics for a water quality station such as a unique ID, display name, latitude/longitude coordinates, associated sector and sensors, and comments. The following table lists the supported fields.

Field Name	Description	Priority	Data Type	Constraints	Unit
WaterQualityStationId	The unique identifier of the water quality station	Required	string
Description	A full name or description of the water quality station	Optional	string	Max length: 255
SectorAreaId	The unique identifier of the sector that is linked with the water quality station	Optional	string
Latitude	The latitude of the point in GPS coordinates	Optional	double	Must be in range from -90 to 90	degrees
Longitude	The longitude of the point in GPS coordinates	Optional	double	Must be in range from -180 to 180	degrees
Sensors	Associated sensors with space separated	Required	string
ValidFrom	The start of the range which defines the areas affected by the import	Optional default: 0001-01-01	date	Must be the start of a month. (for example, 2020-05-01) and lesser than 'ValidUntil'
ValidUntil	The end of the range which defines the areas affected by the import	Optional default: 9999-12-31	date	Must be the start of a month. (for example, 2020-05-01) and greater than 'ValidFrom'
Comment	Comment field	Optional	string	Max length: 255
DisplayName	The display name of the water quality station	Optional	string

3298371: Support for persistence of user preferences

User experience improvements have been implemented to create a more seamless experience, ensuring the user's preference settings are saved and maintained as the user navigates between the various screens and modules of Temetra Analysis.

3298978: Support for additional sensor types in configuration file

The configuration.csv import file supports new sensor types, allowing users to monitor and visualize data from a broad variety of sensors present in the water distribution network. The following table lists the supported fields.

Field Name	Description	Priority	Data Type	Constraints	Unit	Allowed Values
SensorId	The unique identifier of the sensor	Required	string	50
Description	A long description of the sensor	Optional	string	200
Type	A code that indicates the type of sensor	Required	enum	Cannot be changed if the sensor is already bound to a DMA		P: pressure Q: flow H: water level sensor I: index based volumetric V: volumetric sensor E: energy sensor VOLT: voltage sensor A: current sensor PS: status sensor CL: chlorine sensor PH: pH sensor TU: turbidity sensor TDS: TDS sensor Y: conductivity sensor T: temperature sensor PF: PowerFactor sensor N: PumpSpeed sensor
Unit	The unit of measure of reading values emitted by the sensor	Required	string	10		l/s l/m l/h m mH2o bar m3 gal (US)/s gal (US)/m gal (US)/h kWh V A DegreeCelsius rpm ppm NTU mS/cm mg/L N/A (for PowerFactor, PH, and PowerStatus)
Granularity	The length of time between each sensor reading	Required	integer		minutes	5 15 60
SensorLocationId	Location ID from Sensor Location file	Required	string
Rmse	Field description is TBD	Recommended	double	No maximum
EpanetId	The identifier of the sensor in the EPANET model	Recommended	string	50
IsCritical	Whether the sensor is a critical sensor or not	Ignored	bool
IsVirtual	The flag shows whether a sensor is real. Tanks may have virtual sensors.	Optional	bool	'true' indicates virtual 'false' indicates real		true false
DialConfiguration	Assists users in accurately reading sensors	Optional	decimal (9,6)	Greater than 0
Diameter	Diameter of the sensor	Optional	decimal (9,6)	Greater than 0
EndpointId	Endpoint ID associated with the sensor	Optional	string
Comments	Any detail can be added here for a sensor	Optional	string	255

Resolved issues

This section lists significant issues that have been addressed in this Temetra Analysis release.

3214010: Leakage event scoring job issue

In Event Investigation, the leakage event scoring job failed to execute properly. This issue has been resolved.

3222134: Clearing option not resetting filters

In Event Investigation views, the Clear All Filters (or Clear All Preferences) option was not clearing filters and resulted in an error. This issue has been resolved.

3287363: Incorrect data on service point entity page

In Event Investigation, the Service Point ID (entity) page displayed incorrect last-interval data and consumption data. This issue has been resolved.

3296615: Sensor display issue on sectors map

In Transmission Mains Monitoring, sensors were not properly displaying on the Sectors map. This issue has been resolved.

3301367: Leakage/hour column displaying incorrect data

In Event Investigation, the Detect Customer Leakage table displayed incorrect data in the Leakage/hour column. This issue has been resolved.

3310802: ServicePoint data import issue

An issue with the import of ServicePoint data and related error description has been resolved.

3318776: Import job error description issue

The processing of the Meter.csv configuration file rendered inadequate descriptions of error messages for import jobs. This issue has been resolved. Error messages now provide more descriptive and helpful information about the root cause of import job errors.

About this release

This Temetra Analysis release is automatically applied for hosted Software as a Service (SaaS) customers on the release date. For managed appliance customers, Temetra Analysis releases are managed by Itron and may use a different schedule.

Enhancements

This section lists new or updated functionality included in this Temetra Analysis release.

3134565/3134571/3145381: Added daily, monthly, and yearly KPIs to DMA entity page

In Operational Visibility, Daily KPI, Monthly KPI, and Yearly KPI tables have been added to the DMA ID (entity) page. See DMA ID (entity) page.

3149012: Low-frequency data import support

The meter interval reading (indices) import file, Indices.csv, has been improved to ensure continuity of meter consumption data following a meter change-out and eliminate scenarios in which meter change-outs result in significant negative spikes in measured consumption.

3169679: Persistence of pinned column in regions table

in Operational Visibility, the List of Regions table now allows for a column to be pinned by a user and remain pinned after the user has navigated to a different screen. For more information, see List of regions.

3175520: Identification of duplicate Imports and type mismatches

Improvements to the data import process have been made to automatically identify duplicate meter/sensor IDs and device-type mismatches. Users are notified of the existence of duplications or mismatches so that the appropriate actions can be taken. This functionality minimizes data-cleaning activities associated with data imports and ongoing management of the system.

3187228: Water balance daily, monthly, and hourly selection enhancement

On the Operational Visibility Region page, the icons denoting daily/monthly/hourly water balance have been relocated and combined to create more space for the chart and scrolling bars. The icon changes to indicate the current selection. For more information, see DMA chart.

3189390: Updated equations for polygon color coding

For maps in Operational Visibility maps with Priority KPI color coding and map legends, the equations used to define the color-coding thresholds of DMA polygons have been refined. For more information, see Region map and DMA map.

3194880: DMA IDs and descriptions added to dashboard cards

On the Dashboard, DMA IDs and DMA descriptions have been added to dashboard cards to allow for easy identification. This enhancement applies to the Decile Analysis, DMA Overview, and Large Consumers dashboard cards.

3217403: Added columns to sensor file import

The Sensor.csv import file supports new configuration attributes for sensors, including Dial Resolution, EndpointID, and Comments. The inclusion of Dial Resolution for sensors is primarily used for an index meter to allow for the automatic detection of rollover events, maintaining continuity of data following the rollover and improving the quality of the data displayed in Temetra Analysis. The inclusion of EndpointID indicates which communication endpoint provides connectivity for a sensor, which is helpful in diagnosing problems if data is not being routinely delivered for a particular sensor. The inclusion of Comments allows users to provide commentary, notes, or descriptions about particular sensors.

3217406: Filtered column highlighting enhancement

Tables with columns that support filtering now feature highlighted column headers for columns with filters applied, allowing for easy identification of filtered columns. These column headers appear in a different color than unfiltered column headers.

3222176: Added Dial Configuration field to meter configuration

The Meter.csv configuration file now supports a Dial Configuration field. When combined with meter register data, this field allows for the automated detection of meter rollovers, maintaining continuity of water consumption data following a meter rollover event. This enhancement enables users to view the Dial Configuration of a given metering asset and ensures the quality of the data displayed in Temetra Analysis.

3222525: Support for meter index import to ignore non-meter device data

For the in Meter Index Import (Indices.csv), a new feature has been implemented to automate data cleaning and avoid data duplication when non-meter sensor data is included. Temetra Analysis now automatically recognizes non-meter sensor data in a Meter Index Import file, ignores that data, and notifies the user that non-meter sensor data will be ignored during the import. This ensures that data import files contain only meter-related data and improves the quality of the data displayed in Temetra Analysis.

Resolved issues

This section lists significant issues that have been addressed in this Temetra Analysis release.

3214010: Leakage event scoring job issue

In Event Investigation, the leakage event scoring job failed to properly execute. This issue has been resolved.

3217360: Sensor data units of measurement issue

In the Event Investigation Sensors view, the configured units of measurement for sensor data did not display consistently. This issue has been resolved.

3222164: Daily KPI not showing current dates

In Operational Visibility, the Daily KPI on the DMA ID (entity) page displayed incorrect dates in the Date column. This issue has been resolved.

3224872: Water balance job executing for inactive DMAs

In Operational Visibility, the DMA water balance job was being executed for DMAs with a status set to inactive. This issue has been resolved.

About this release

This Temetra Analysis release is automatically applied for hosted Software as a Service (SaaS) customers on the release date. For managed appliance customers, Temetra Analysis releases are managed by Itron and may use a different schedule.

Enhancements

This section lists new or updated functionality included in this Temetra Analysis release.

2844532: Sectors view enhancements

In Transmission Mains Monitoring, the Sectors table features new columns for both daily and monthly views: Total Loss and Loss/Length. For information about viewing this table, see Sectors table.

2894293: DMA Type column in Event Investigation

In Event Investigation's Detect, Review, and Silence Data views, the AMI Meter column has been replaced with the DMA Type column, enabling users to determine the specific type of DMA associated with service points.

3145378: DMA water balance view enhancements

On the Operational Visibility Region page, the new DMA ID (entity) page features monthly, daily, and hourly view options, as well as the ability to toggle between Basic and Full water balance views. Users can access monthly water balance data, daily data for any 90-day period, and hourly data for any 31-day period. For more information, see DMA ID (entity) page.

3145959: Added DMA ID (entity) page

In Operational Visibility, the DMA ID (entity) page displays various attributes for the selected DMA in an easy-to-read format. The DMA Details panel on the entity page indicates the Supply Type for each DMA and a timestamp of the last successful run of the water balance job. For more information, see DMA ID (entity) page.

3148554: List of DMAs table usability improvement

On Operational Visibility Region pages, the List of DMAs table (list view) includes a usability improvement. Previously, selecting the same row twice would cancel the current DMA selection. Selecting a DMA row a second time would cause all other panels to shift to region mode and show region information. Now, users must select another DMA or region to access the desired data instead of deselecting the current selection.

3166732: Expanded account type support

Temetra Analysis now supports the identification of a broader range of account types beyond the previously supported options (Residential, Commercial, Industrial, and null). Sixty-two new account types (including null, now labeled as Unknown) are now supported for the ServicePointv2.csv import file (AccountTypeId column) and the user interface to accommodate these enhancements.

Resolved issues

This section lists significant issues that have been addressed in this Temetra Analysis release.

3123928: Localization issue across various application segments

Some screens did not display text in the language consistent with the configured localization setting (FR-fr, PT-pt, and ES-es). This issue has been resolved.

3160540: Service point daily view not loading dates

In the Event Investigation Service Point view (daily), dates for specific service point IDs failed to load properly. This issue has been resolved.

3164583: DMA water balance computation issue

On Operational Visibility's DMA ID (entity) pages, improper computation of the DMA water balance occurred when using hourly interval consumption data. This issue has been resolved.

3166870: Missing sensor data

On the Operational Visibility DMA sensor chart, missing data (instead of zero consumption) was shown for sensors delivering consecutive readings with the same consumption index. This issue has been resolved.

3167970: Apparent loss results not reflecting priority KPI

On Operational Visibility's Region page, results for Apparent Loss % of the selected DMA did not correspond correctly with the priority KPI selected on the DMA map. This issue has been resolved.

3168028: DMA color issue with Total Loss priority KPI

On Operational Visibility's Region page, the wrong colors displayed for DMAs on the map when Total Loss was the selected priority KPI. This issue has been resolved.

3169172: Region and DMA color issue due to incomplete configuration file

On Operational Visibility's Region page, the wrong colors displayed for regions and DMAs on the map when the unit of measure scope was not provided in the user configuration file. This issue has been resolved.

3170401: Default water balance chart issue

In the Operational Visibility DMA chart, Water Balance (Basic) is the default selection, but Water Balance (Full) displayed by default instead. This issue has been resolved.

3174378: Consumption data import error

Meter-read data loaded via the Consumption.csv import file resulted in a logged error if the associated service point information had not yet been loaded into the tenant. This issue has been resolved. Incoming meter reads that have not yet been associated to a service point are now stored instead of being rejected by the system.

3179705: Monthly water balance export file issue

In Operational Visibility, the DMA ID (entity) page supports exporting monthly, daily, or hourly water balance data to a CSV file. However, the monthly export option resulted in an export file containing extra months with blank entries, and its file name appeared with "null" appended to the name instead of the date range for the export. This issue has been resolved.

3187386: Hourly water balance timestamp issue

On the DMA ID (entity) page in Operational Visibility, the hourly water balance chart displayed an incorrect timestamp (on hover). The hourly export option also produced an incorrect timestamp in the export file. This issue has been resolved.

About this release

This Temetra Analysis release is automatically applied for hosted Software as a Service (SaaS) customers on the release date. For managed appliance customers, Temetra Analysis releases are managed by Itron and may use a different schedule.

Enhancements

This section lists new or updated functionality included in this Temetra Analysis release.

2893334: Water Balance job management engine enhanced for high-frequency data

The job management engine for Water Balance data has been upgraded. Water Balance charts render high-frequency data from new schema tables containing values calculated from scheduled daily execution jobs.

2927019: Units of measurement support for SCADA import file

The Temetra Analysis system can import configuration and bulk data through CSV files, including those from SCADA systems. The ScadaData.csv import supports both imperial and metric units. Newly supported imperial units include flow (gal/s, gal/m, gal/h), pressure (psi), and volume (gallons, cubit feet). The system also supports unit conversion for imported data. For units information, see Units of measurement.

2953287: Near real time job calculations for water balance

Water Balance calculations support imported water balance and event jobs data for the current day and up to the most recent hour that data is available. For DMAs or sectors with hourly or sub-hourly data, the ability within Temetra Analysis to update the hourly water balance as data arrives. This is currently limited to a process running once an hour. Results are processed 15 minutes past the local hour.

2955503/2955504/2955505: Sensor view enhancements

In Event Investigation, the Sensors table features new columns for both daily and monthly views: Count of Readings, Percentage of Data, Average of Readings, Min. Reading, Max. Reading, Negative Readings Count, Negative Sum of Readings, Maximum Negative Reading, Standard Deviation, Average Daily Usage (ADU 30 and 365), Percent of Change (Month), Percent of Change (Year), Percent of Change (Day), Daily/Monthly Change (Units), Latitude, Longitude, Reading Interval, Unit of Reading, IsCritical, Inflow, Outflow, Last Reading DateTime, Latest Reading Value, and Other. For the daily view, an ADU 7 column has been added.

The Daily/Monthly Change (Units) cells are color coded to indicate increases (red) and decreases (green). The Percent of Change (Month), Percent of Change (Year), Percent of Change (Day) cells are color coded for configurable thresholds to indicate relative rates of change, with shades of red for increases and shades of blue for decreases (darker shades correspond to higher rates of change). For more information, see Event Investigation page and Service point and sensor information.

2955460: Service Points view enhancements

In Event Investigation, the Service Points table features new columns for both daily and monthly views: Active Leak, Active Zero Reads, Active No Reads, Decile Group, Confidence Bounds, Count of Readings, Percent of Readings, Sum of Readings, Max Reading, Min Reading, Standard Deviation, Average of Readings, Negative Readings Count, Zero Reading Count, Maximum Negative Reading, and Average Daily Usage (ADU 30 and 365), Daily/Monthly Change (Units), Percent of Change (Month), Percent of Change (Year), and Percent of Change (Day). For daily views only, columns ADU 7 and Reading (0–23) have been added.

The Percent of Change (Month), Percent of Change (Year), Percent of Change (Day) cells are color coded for configurable thresholds to indicate relative rates of change, with shades of red for increases and shades of blue for decreases (darker shades correspond to higher rates of change). For Active Leak and Active No Reads, cells are shown in red if the value is True. For more information, see Event Investigation page and Service point and sensor information.

2955499: Sectors view enhancements

In Transmission Mains Monitoring, the Sectors table features new columns for both daily and monthly views: Last Processed DateTime, Maximum Flow, Working Pressure, Pipe Length, and Valid Until. For more information, see Sectors table.

3013927/3013982: Sensors entity page with pressure and readings charts

In Event Investigation, a Sensor ID (entity) page has been added to provide graphical representations of a selected sensor's pressure and readings data over time, as well as a list of all sensor details. The Sensor ID page is accessed from the Sensor analytics table on the Event Investigation page. For details, see Sensor ID (entity) page.

3024350: Regions view enhancements

In Operational Visibility, the List of Regions table has been updated with additional fields, sortable columns, column filters, and CSV/Excel export options. For more information, see List of regions.

3026762: Entity page opens in a new browser tab

In Event Investigation tables, clicking an icon in the Entity column opens the selected entity page in a separate browser tab.

3026964: DMA units enhancements

In Operational Visibility, the List of DMAs table has been updated with support for imperial units for consumption flow and losses. In addition, the following fields have been added: Description, Apparent Losses (gal (US)), Real Losses (gal (US)), Metered Consumption (gal (US)), Unauthorized Consumption (gal (US)), DMA Valid From, DMA Valid Until, Is Active, and Last Processed Date Time. The List of DMAs table supports hierarchy visualization of Region to DMA with aggregation of DMA metrics up to the regional level. The table also features a date picker, a monthly/daily toggle, sortable columns, column filters, chart view options for selected cells, CSV and Excel export options, and a map view option. For more information, see List of DMAs.

3034816: Endpoint ID column added to Event Investigation

In Event Investigation's Detect views, an Endpoint ID column option has been added.

3034855: Region water balance charts reflect the same DMA granularity

In Operational Visibility, for any region that contains DMAs with the same level of granularity (monthly, daily, hourly) as the parent region, the region water balance chart displays the same levels of granularity.

3035636: Month/day information removed from Sectors table column headers

In Transmission Mains Monitoring, column headers in the Sectors table no longer include day or month information, as this information is shown in the table header date picker.

3039395: DMA map supports color-coded changes over time

In Operational Visibility, the DMA map on the Region page supports color coding based on the selected day or month when the priority KPI is set to Real Loss or Apparent Loss. To view changes over time, select the day or month with the date picker above the map. For details, see DMA map.

3068459: KPI selection persists until changed

In Operational Visibility, the KPI selection for region and DMA maps persists until changed (such as ILI, Real Loss, and Apparent Loss). The KPI selection will remain selected after the user navigates away and then back, or when the user signs out and then signs in again.

3073435: DMA Selector table enhancements

In Model Visualization, the DMA Selector table has been updated to support sortable columns, column filters, and other enhancements consistent with all tables within Temetra Analysis. For more information, see DMA selector table.

3097918: Improved access to service point entity pages

All features of Service Point ID (entity) pages (interval data, consumption trend, etc.) can now be accessed from any Event Investigation table where a given service point is listed.

3099121: DMA ID and DMA Description columns updated in Event Investigation

In Event Investigation's Detect tables, columns with DMA identifiers are now named DMA ID, and a DMA Description column has been added. These changes correspond to the List of DMAs tables on Operational Visibility Region pages.

3099145: Reduced column width in tables

In Event Investigation and Transmission Mains Monitoring, table columns have been narrowed to conserve screen space. All column widths may be manually adjusted as needed.

3099890: General Reports displays all uploaded reports

In Water Reports & Tools, the General Reports tab now displays all uploaded reports regardless of upload date, instead of only those from the past month.

Resolved issues

This section lists significant issues that have been addressed in this Temetra Analysis release.

2988504: Filter issue with Meter Diameter column in imperial units

In Event Investigation tables, column filtering with the "Greater than" operator for the Meter Diameter column did not return expected results when units of measurement were set to imperial. This issue has been resolved.

3062232: DMA Meter Gain chart displays no results

On the Operational Visibility Region page, the DMA chart, with the Meter Gain graph selected, displayed no data for the selected DMA. This issue has been resolved.

3063988: Localization issue for newly added columns in Sectors table

In Transmission Mains Monitoring, user-selected columns in the Sectors table were not being labeled in the language consistent with the configured localization setting. For example, newly added column headers displayed in English when Spanish was expected. This issue has been resolved.

3076283: Sensor ID entity readings chart x-axis text issue for non-English languages

In Event Investigation, the readings chart on the Sensor ID (entity) page displayed unreadable text on the x-axis for non-English localization environments. This issue has been resolved.

3078551: Region detail ALI field displays 'NaN' instead of 'N/A'

In Operational Visibility, the Losses tab in the Region details panel displayed a value of "NaN' in the Apparent Loss Index (ALI) field when "N/A" was expected. This issue has been resolved.

3080481: For tenants with imperial units, Meter Diameter (DN) values display incorrectly

In the Event Investigation Service Points table, values in the Meter Diameter (DN) column did not display correctly for tenants with imperial units of measurement. This issue has been resolved.

3081660: Boolean filter issue for newly added columns in Service Points table

In the Event Investigation Service Points table, column filters for user-selected columns with Boolean values (True/False) did not produce the expected results. This issue has been resolved.

3083008: Service Points daily Reading values display decimal places exceeding configured limits

In Event Investigation, the custom Reading columns in the Service Points table's daily view displayed values with 10 or more decimal places. This issue has been resolved. The Reading values now display up to three decimal places, depending on user configuration.

3083084: Service Points monthly views display no values in filtered columns

In Event Investigation, columns with applied filters in the Service Points table's monthly view did not display filtered values as expected. This issue has been resolved.

3084120: Service Points page not displaying correctly in selected language

In Event Investigation, the Service Points screen (daily and monthly views) did not display text in the language consistent with the configured localization setting. This issue has been resolved.

3085465: Automated execution deleting Water Balance values

In Operational Visibility, the Water Balance chart displayed values of zero for the selected date range following an automated water balance read. However, these values were restored and displayed correctly after executing a manual water balance read. This issue has been resolved.

3086820: Total Inflow, outflow, and losses displaying 'NaN' values

In Transmission Mains Monitoring, the Sectors table displayed values of "NaN' in the Total Inflow, Total Outflow, and Total Loss columns. This issue has been resolved. See also resolved issue 3078551.

3086831: Dashboard DMA cards displaying no data

On the Dashboard, the DMA Overview, Decile Analysis, and Large Consumers cards displayed no data for the configured DMA. The cards appeared to be loading but did not complete the loading process. This issue has been resolved.

3087541: Active Leak, Active Zero Reads, and Active No Reads columns not displaying value of False

In the Event Investigation Service Points table, the Active Leak, Active Zero Reads, and Active No Reads columns are designed to provide Boolean values (True/False) but displayed empty cells for the "False" condition (no event present). This issue has been resolved.

3087645: Decile Group values represented as strings instead of integers

In the Event Investigation Service Points table, the Decile Group column represents groups with whole number values of 1 through 10. Values in this column were represented as text strings instead of integers, affecting sorting behavior. This issue has been resolved. Decile Group values are now stored as integers to support accurate sorting.

3093606: Unable to filter decimal values for Average of Readings column

In the Event Investigation Sensors table, the Average of Readings column filter provided the options of True, False, and Blank, preventing the filtering of decimal values. This issue has been resolved. The Average of Readings column filter now supports a search field with a dropdown menu for operator options (Equals, Greater than, Less than, etc.).

About this release

This Temetra Analysis release is automatically applied for hosted Software as a Service (SaaS) customers on the release date. For managed appliance customers, Temetra Analysis releases are managed by Itron and may use a different schedule.

Enhancements

This section lists new or updated functionality included in this Temetra Analysis release.

2929816: Added End Point ID and Meter Multiplier fields

The ServicePoint.csv and sensor.csv import files now support two new fields: End Point ID and Meter Multiplier. In the Event Investigation user interface, these fields appear in the Service Points report. See also enhancement 2935588.

2931859: Added Sector Status dashboard card

The Sector Status dashboard card provides a summary of a selected sector's total inflow, total outflow, total losses, and volume gain. The card supports a threshold configuration for total losses. If the configured threshold has not been exceeded, the card background appears blue, but if the configured threshold has been exceeded, the background appears red.

2935588: Added Service Points report option

In Event Investigation, a Service Points report option has been added. The Service Points report displays all service points within a region and supports comparing service points and performing a general analysis of the data set. For more information, see Event Investigation page. See also enhancement 2953587/2955458.

2937302: DMA view enhancements

In Operational Visibility, the List of DMAs table has been updated with support for imperial units for consumption flow and losses. In addition, the following fields have been added: Description, Apparent Losses (gal (US)), Real Losses (gal (US)), Metered Consumption (gal (US)), Unauthorized Consumption (gal (US)), DMA Valid From, DMA Valid Until, Is Active, and Last Processed Date Time. The List of DMAs table supports hierarchy visualization of Region to DMA with aggregation of DMA metrics up to the regional level. The table also features a date picker, a monthly/daily toggle, sortable columns, column filters, chart view options for selected cells, CSV and Excel export options, and a map view option. For more information, see List of DMAs.

2942602: Added customer leakage chart

In Event Investigation, the Interval Data panel now includes a graph showing the daily leakage rate for the service point selected from the Customer Leakage report. For more information, see Interval data (leakage).

2948261: Support for high-granularity temporal updates

Daily temporal changes are supported within Temetra Analysis, providing the ability to reflect high-granularity updates such as the following actions:

• Adding, removing, or updating service points within a DMA

• Transferring service points from one DMA to another

• Adding, removing, or updating sensors associated with a DMA

• Adding, removing, or updating new DMAs within a region

Water balance and associated calculations support daily temporal changes, as well as other graphs and calculations related to temporal changes (such as the number of meters within a DMA on a given day). Event Investigation screens also reflect service point additions, removals, and changes to DMA associations.

2948379: Report file upload/download capability

In Water Reports & Tools, authorized users can download and upload reports from the user interface. The supported file types are .pdf, .xlsx, and .docx. A mechanism to automatically import files from a separate solution is also supported. For more information, see General reports.

2953587/2955458: Service Points navigation and report enhancements

In Event Investigation, a Service Points menu category has been added to the View Menu. Within this category is the Service Points report option. The Service Points table features a date picker and a monthly/daily toggle to allow for historical visualization of service point status, sortable columns, column filters, and CSV and Excel export options. See also enhancement 2935588.

2955496/2955501: Sector view enhancements

In Transmission Mains Monitoring, the Sectors table now features a date picker, a monthly/daily toggle, sortable columns, column filters, chart view options for selected cells, and CSV and Excel export options. For more information, see Sectors table.

2999983: Added Sensors report with map view

In Event Investigation, a Sensors menu category has been added to the View Menu. Within this category is the Sensors report option. The Sensors report displays all sensors within a region and supports comparing sensors and performing a general analysis of the data set. For sensors with latitude and longitude information, a map view is supported. The Sensors table features a date picker and a monthly/daily toggle, sortable columns, column filters, and CSV and Excel export options. For more information, see Event Investigation page.

3004376: Tank Level gap-fill calculation updated to correct volume gain or loss

In Transmission Mains Monitoring, the Tank Level chart now uses a gap-fill method to correct for missing readings from a water level sensor by using the last known reading in its calculation. When a missing reading becomes available later, the calculation includes the newly available reading.

3011621: Updated calculation method for Customer Leakage score

In Event Investigation, the calculation method to determine the Customer Leakage score was based on the lowest read value within the Minimum Night Flow (MNF) interval. The calculation method has been updated to take the lowest read value from a full day (24 hours).

3020819: Dashboard Sector Status card color-coded to reflect daily total loss volume

On the dashboard, the Sector Status card supports a threshold configuration for total losses. If the configured threshold has not been exceeded, the card background appears blue, but if the configured threshold has been exceeded, the background appears red. For more information, see Dashboard.

Resolved issues

This section lists significant issues that have been addressed in this Temetra Analysis release.

2929647: Data rows missing from Consumption Confidence export file

On the Operational Visibility Region page, the CSV export file generated from the Consumption Confidence chart omitted data rows for months with missing hourly readings within a DMA. This issue has been resolved.

2936537: Interval data chart CSV export file displays incorrect timestamp date

In Event Investigation, the Interval Data chart on a Service Point ID (entity) page supports exporting the data to a CSV file. In the export file, the Timestamp column contained timestamp values with the last date of each month instead of the start date of each month. This issue has been resolved.

2967839: Tank level readings (calculated and actual) displayed with jagged lines

In Transmission Mains Monitoring, the Tank Level chart on the Sector ID page for a tank entity displayed jagged lines for calculated and actual tank levels instead of smooth lines. This issue has been resolved.

2973577: Customer leakage chart not displaying values if selected end date doesn't have data

In Event Investigation, the Interval Data customer leakage chart on a Service Point ID (entity) page displayed no value if no data was associated with the selected end date. This issue has been resolved.

2979420: Columns missing from Zero Consumption table

In Event Investigation, the Zero Consumption table was missing the following columns: Account Number, Last Analysis Date, 'Last Read Date, Zero Consumption Start Date, and No of Days With Zero Consumption. This issue has been resolved.

2979494: Columns missing from Consumption Trend table

In Event Investigation, the Consumption Trend table was missing the Account Number and Last Analysis Date columns. This issue has been resolved.

2985023: DMA sensor map toggles switches not displaying in Edge browser

In Operational Visibility, the DMA sensor map's legend contains toggle switches to customize the map view but did not display in the Microsoft Edge browser. This issue has been resolved.

2985193: Customer leakage chart out of sync with interval data chart

On the Service Point ID (entity) page in Event Investigation, the x-axis timeline of the customer leakage chart was out of sync with the x-axis timeline of the interval data chart in the same panel. This issue has been resolved.

About this release

This Temetra Analysis release is automatically applied for hosted Software as a Service (SaaS) customers on the release date. For managed appliance customers, Temetra Analysis releases are managed by Itron and may use a different schedule.

Enhancements

This section lists new or updated functionality included in this Temetra Analysis release.

2843300: Persistence of column filters during browsing session

For tables with column filtering, all applied filters now persist for the duration of the current browsing session. When a user navigates to another screen and then returns to the table, setting the filters again is not necessary to view the same results. To reset the filters, click Clear All Filters above the table.

2843541: Tank water balance chart

In Transmission Mains Monitoring (formerly Water Network), a Tank Water Balance chart is now available for tank entities. This chart provides inflow, outflow, and tank level data for the selected water-tank sector during the selected date range. See Tank level.

2878244: Persistence of column sizing during browsing session

For tables with column controls, all applied width adjustments now persist for the duration of the current browsing session. When a user navigates to another screen and then returns to the table, setting the widths again is not necessary to retain the same view.

Resolved issues

This section lists significant issues that have been addressed in this Temetra Analysis release.

2849289: Interval data chart not re-adjusting y-axis range

In Event Investigation (formerly Consumer Analytics), the Interval data chart did not correctly re-adjust the y-axis to reflect the visible range when the user zoomed in on the x-axis timeline to view detailed data. This issue has been resolved.

2859627: Negative y-axis values shown on zero consumption chart

On the Operational Visibility Region page, the DMA chart panel beneath the map supports several options, including Zero Consumption. With this option selected, the y-axis representing the number of connections with zero consumption displayed both positive and negative values in its range. The y-axis should display positive values only. This issue has been resolved.

2872647: Leak areas not highlighted on DMA map

On the Operational Visibility DMA map, leak pressure areas did not display as green sections on the map when the leak localization toggle switches for the DMA were in the on position. This issue has been resolved.

About this release

This Temetra Analysis release is automatically applied for hosted Software as a Service (SaaS) customers on the release date. For managed appliance customers, Temetra Analysis releases are managed by Itron and may use a different schedule.

Enhancements

This section lists new or updated functionality included in this Temetra Analysis release.

2790803: DMA sensor time-series chart shows decimated data instead of average values

In Operational Visibility, data points were averaged in the DMA sensor chart for data over a wide time span. With this update, the application performs decimation (reduced sampling) so that the actual values of data points display on the chart.

2807031: Water Balance calculation update

In Operational Visibility, Water Balance charts no longer contain functionality that forces water balance calculations to show zero for real and apparent losses. This applies to scenarios in which metered consumption is greater than supplied water during the Minimum Night Flow (MNF) period.

2815764: Event Investigation table filtering enhancements

In Event Investigation (formerly Consumer Analytics), views have been enhanced with column-specific filtering capabilities for each table on the Event Investigation page.

2838983: Zero Consumption grid lines added

In Event Investigation (formerly Consumer Analytics), grid lines have been added to Zero Consumption charts on entity pages.

Resolved issues

This section lists significant issues that have been addressed in this Temetra Analysis release.

2744828: Missing or incorrect translations for French localization

In Operational Visibility, with the browser set to French (France), some text strings in the UI appeared in English or were missing. This issue has been resolved.

2801447: Consumption trend export files show incorrect timestamp format

On Event Investigation (formerly Consumer Analytics) entity pages, exported CSV data from consumption trend charts contained the wrong date format in the Timestamp column (month-year instead of year-month). This issue has been resolved.

2803069: DMA critical pressure sensors not shown in red on the map

In Operational Visibility, critical pressure sensors on the DMA sensor map did not display as red icons when the critical threshold had been met as defined in the configuration file. This issue has been resolved.

2813573: Event Investigation column order not persisting

In Event Investigation (formerly Consumer Analytics), reordering the columns of any table is supported by dragging a column header to the desired location. However, persistence of updated column order was not maintained when the user navigated back from other screens. This issue has been resolved.

2815251: Color coding for customer leakage score not correctly displayed

In Event Investigation (formerly Consumer Analytics), the Review tables did not display the correct color coding in the Customer Leakage Score column. This issue has been resolved.

2817595: DMA sensor chart not zooming correctly

In Operational Visibility, zooming in on a time span within the DMA sensor chart did not reveal high-granularity data over a short period of time. This issue has been resolved.

2835356: Missing or incorrect French translations in region and DMA properties panels

In Operational Visibility, with the browser set to French (France), some property fields in the Region details and DMA information panels appeared in English or were missing. This issue has been resolved.

2837051: Incorrect date range localization in sector water balance chart

In Transmission Mains Monitoring (formerly Water Network), the sector >Water balance chart displayed an incorrect date/time format for countries outside of North America. This issue has been resolved.

About this release

This Temetra Analysis release is automatically applied for hosted Software as a Service (SaaS) customers on the release date. For managed appliance customers, Temetra Analysis releases are managed by Itron and may use a different schedule.

Enhancements

This section lists new or updated functionality included in this Temetra Analysis release.

2751939: Data export from DMA time series chart

In Operational Visibility, exporting data from the time series chart on the DMA screen now results in all sensor data being exported, regardless of the granularity shown in the chart.

2772446: Print button for reports

In Water Reports & Tools, a Print button now enables a snapshot of the Power BI reports screen to be printed or saved to PDF.

2785027: Combined tooltip in charts

In Operational Visibility, each Region DMA chart now features a combined tooltip on hover to show exact values.

2799277: Consumer leakage score calculations

In the Customer Leakage tables in Event Investigation (formerly Consumer Analytics), the algorithms for calculating Consumer Leakage Score 1, Score 2, and Score 3 have been updated to reflect the following conditions:

• Consumer Leakage Score 1. The number of days until the cost to the consumer exceeds the cost of fixing the leak.

• Consumer Leakage Score 2. The average daily consumer cost of the leak over the observation period.

• Consumer Leakage Score 3. The estimated 100-day cost to the consumer due to the leak.

Resolved issues

This section lists significant issues that have been addressed in this Temetra Analysis release.

2776215: Property panel screen shaking when region is selected

In Operational Visibility, the region map and adjacent panels sometimes appeared to shake, depending on the browser width. This issue has been resolved.

2791127: Total leakage volume displayed as negative value

In Consumer Analytics, the Total Leakage Volume column in the Customer Leakage table showed negative values for meters with no negative consumption. This issue has been resolved.

2791174: Leakage/hour and Total leakage Volume showing two decimal places for values

In Event Investigation (formerly Consumer Analytics), the Leakage/hour and Total Leakage Volume columns in the Customer Leakage table showed values in cubic meters (m³) with only two decimal places instead of three. This issue has been resolved.

2791185: Water balance chart showing NRW value of greater than 100%

In Operational Visibility, the water balance chart on the Region page showed non-revenue water (NRW) values that exceeded 100% (positive or negative). This issue has been resolved. The maximum NRW value has been capped at 100%.

2801814: Incorrect sorting in Start Date of Leak column

In Event Investigation (formerly Consumer Analytics), the Start Date of Leak column in the Customer Leakage table, when sorted by descending order, displayed dates from past years at the top of the list instead of newest dates first. This issue has been resolved.