Gen5 Intelis Gas Meter Events
Event code |
Event name |
Event description |
---|---|---|
2 |
Register error |
No communication with register. Note: For the Intelis Gas meter, this corresponds to the "Loss of Meter Communication" tamper bit in Mobile mode which could indicate the index has been removed from the meter. |
5 |
Magnetic detected |
The ERT has detected an external magnetic field. |
6 |
Low battery |
The ERT has a low battery warning. 10% of battery life remains. |
9 |
Reverse flow detected |
The ERT has detected reverse flow. |
10 |
Reverse flow end |
The ERT has detected the end of reverse flow after having reported reverse flow. |
14 |
Valve OK |
The ERT detects that a remote disconnect valve is attached and it is working properly (triggered when state was previously unknown or previously not working properly). |
15 |
Valve No Comms |
The ERT detects a remote disconnect valve is attached but it is not working properly. |
22 |
Extended high flow detected |
The ERT detects consumption has exceeded the high flow threshold. |
23 |
Extended high flow end |
The ERT detects that consumption has dropped below the high flow threshold after having been in a high flow state. |
24 |
High temperature detected |
The device detects that the temperature has exceeded the high temperature threshold. |
25 |
High temperature end |
The device detects that the temperature has dropped below the high temperature threshold after having been in a high temperature state. |
26 |
Air in pipe detected |
The device detects air in the meter, possibly due to the meter being removed from the installation. |
27 |
Air in pipe end |
The device no longer detects air in the meter. |
500 |
Critical error (internal) |
A critical internal error not described by other events. |
504 |
Flash error |
A flash error has been detected. |
505 |
Meter quiet mode exit |
Occurs when the ERT gets pulses or detects consumption for the first time. |
506 |
Entering OW Riva network mode |
The device has been changed to OpenWay Riva network mode. |
507 |
Set battery params |
Any change to the BatteryUseParameters structure results in this event. |
509 |
Key update |
The key has been updated in the device. |
510 |
Device not communicating |
The application has not received any incoming data which indicates that the device may not be communicating on the network. |
511 |
Load profile cleared |
The load profile object has been cleared. |
512 |
Manual time sync |
The time has been changed manually. |
514 |
Legally relevant event log nearly full |
This event occurs when the Legally Relevant log is at 90% of its total capacity. |
515 |
Time sync - over threshold detected |
A time change greater than the warning level threshold has been detected. |
516 |
Time sync - over threshold end |
A time change greater than the warning level threshold has ended and is back below the threshold. |
517 |
Entering 100S mode |
The device has been changed from OpenWay Riva network mode to 100S mode. |
518 |
Entering prover mode |
The device has entered prover mode. |
519 |
Exiting prover mode |
The device has exited prover mode. |
520 |
Flow while disconnected detected |
The valve is in a disconnected state but flow has been detected by the device. Note: This event does not have an end event but is debounced every 24 hours. So, for a device that is continually in this state, the event will be logged once every 24 hours. |
521 |
Button Press/LCD on |
The device push button has been depressed causing the LCD to turn on. Note: This event is logged once each time the LCD is turned on, subsequent button pushes while the LCD is still on will not result in additional events being logged. |
522 |
Flow sensor hard failure |
The device has detected that its flow sensor has failed. An ultrasonic measurement unit (UMU) hard error. This is an unrecoverable error. |
523 |
Flow measurement outside physical range detected |
The device has detected that the flow is outside the physical range of the measurement sensor. Qmin or Qmax exceeded. |
524 |
Flow measurement outside physical range end |
The device has detected that the flow has returned to a level within the physical range of the measurement sensor after having been outside the range. |
526 |
Gas temperature outside sensor range detected |
The device has detected that the gas temperature is outside the range of the temperature sensor (temperature max exceeded, temperature min exceeded). |
527 |
Gas temperature outside sensor range end |
The device has detected that the gas temperature has returned to a value within the range of the temperature sensor after having been outside the range. |
528 |
Flow sensor measurement error |
The device has detected that a flow sensor measurement error has occurred. This is an unrecoverable error. |
529 |
Transducer error |
The device has detected that its ultrasonic transducers have an issue which is reflected by an abnormal gain or an abnormal Tup/Tdown (time required by the ultrasonic signal from the emitter to the receiver). This is an unrecoverable error. |
3000 |
Device reconfigured |
The OpenWay Operations Center (OWCM) configuration in the device has changed. |
3001 |
Event log cleared |
The Itron event log has been reset. |
3003 |
Configuration downloaded |
A new configuration has been downloaded. |
3004 |
System reboot |
A watchdog error. Reboot. |
3005 |
System restart |
A planned restart of ERT (for example, after firmware download). |
3006 |
Improper installation detected |
The ERT could not adopt configuration information. |
3007 |
Disconnect completed |
The disconnect command was received and has completed. |
3008 |
Disconnect failed |
The disconnect command was received but failed to execute. The event detail will contain the verbose_result attribute of the DisconnectControl object. |
3009 |
Arm completed |
The ARM (for reconnect) command was received and has completed. Event detail will contain the verbose_result attribute of the DisconnectControl object. |
3010 |
Arm failed |
The ARM (for reconnect) command was received but failed to execute. Event detail will contain the verbose_result attribute of the DisconnectControl object. |
3011 |
Connect completed |
The reconnect command was received and has completed. Event detail will contain the verbose_result attribute of the DisconnectControl object. |
3012 |
Connect failed |
The reconnect command was received but failed to execute. Event detail will contain the verbose_result attribute of the DisconnectControl object. |
3015 |
Authentication failed |
An application level security failure - authentication. This event occurs with an application level security failure for authentication. |
3016 |
Access control failed |
An application level security failure - access control. This event occurs with an application level security failure for access control. |
3017 |
Key rollover |
A key rollover command received. |
3018 |
Key signing |
An application level security failure - certificate. |
3019 |
Takeover package accepted |
A takeover package was presented and accepted by the ERT. |
3020 |
Takeover package rejected |
A takeover package was presented, but rejected by the ERT. |
3021 |
Replay attack detected |
An application level security failure - replay. |
3022 |
RMA signed authorization received |
A signed authorization with issued-to "Itron-RMA" has been received. |
3024 |
Valve life nearing maximum |
The valve actuation threshold has been exceeded. This will trigger at a count of 76 actuations for the Intelis Gas meter. |
3027 |
Valve operation override |
An override operation has occurred for this valve. |
3028 |
AutoDisconnect initiated |
An auto disconnect occurred in the device. |
3031 |
Prover mode maximum time configuration changed |
A change has been made to the ProverModeMaximumTime. |
3032 |
High flow sampling configuration changed |
A change has been made to the HighFlowSamplingConfiguation. |
3033 |
High temperature configuration changed |
A change has been made to the HighTemperatureEventConfiguration. |
3034 |
HighFlow disconnect enable changed |
The HighFlowDisconnectEnable configuration has changed. |
3035 |
High temperature disconnect enable changed |
The high temperature automatic disconnect configuration has changed. |
3036 |
Air in pipe disconnect enable changed |
The air in pipe automatic disconnect configuration has changed. This event occurs with an application level security failure for access control. |
3037 |
Prover mode pulse width configuration changed |
A change has been made to the ProverModePulseWidth. |
3038 |
Prover mode pulse weight configuration changed |
A change has been made to the ProverModePulseWeight. |
10000 |
PCOMP changed |
Metrology parameter (PCOMP) changed. |
10001 |
Count rate changed |
Metrology parameter (Count Rate) changed. |
10002 |
Rollover count changed |
Metrology parameter (Rollover Count) changed. |
10006 |
Initial index |
Metrology parameter (Initial Index) changed. |
10007 |
Image transfer initiated (enabled) |
An image transfer command was initiated. |
10008 |
Image transfer canceled (disabled) |
An image transfer command was canceled. |
10009 |
Image transfer cancel failed |
An image transfer command was canceled but was not successful. |
10010 |
Image verification initiated |
The process to verify an image has begun. |
10011 |
Image verification successful |
The image verification process was successful. |
10012 |
Image verification failed |
The image verification process was initiated, but was not successful. |
10013 |
Image activation initiated |
The image activation process was initiated. |
10014 |
Image activation successful |
The image activation process was successful. |
10015 |
Image activation failed |
The image activation process was initiated, but was not successful. |
10019 |
Load profile interval changed |
A change has been made to the CompressedLoadProfile object capture_period. |
10022 |
Meter calibrated |
The meter has been calibrated. |
10026 |
Potential index corruption detected |
The device has detected that its index value(s) may have become corrupted. The device should be replaced. |
10027 |
Meter calibrated-A2 value |
A change has been made to the Intelis Gas Meter's UMU calibration A2 value. This event is added to the log when the calibration completes. |
10028 |
Meter calibrated-B1 value |
A change has been made to the Intelis Gas Meter's UMU calibration B1 value. This event is added to the log when the calibration completes. |
10029 |
Meter calibrated-B2 value |
A change has been made to the Intelis Gas Meter's UMU calibration B2 value. This event is added to the log when the calibration completes. |
10030 |
Meter calibrated-B3 value |
A change has been made to the Intelis Gas Meter's UMU calibration B3 value. This event is added to the log when the calibration completes. |