Gen5 500G ERT Module Events

Event code	Event name	Event description
2	Register error	No communication with register.
4	Tilt detected	The tilt detector has been activated, like as a result of physical tampering.
5	Magnetic detected	The ERT has detected an external magnetic field.
6	Low battery	The ERT has a low battery warning. 10% of battery life remains.
16	Tilt debounce parameter changed	The tilt debounce parameter has changed.
20	High flow detected	The ERT detects consumption that exceeds the high flow threshold
21	High flow end	The ERT detects that consumption has dropped below the high flow threshold after being in a high flow state. Note: If the ERT is in a high flow detected state and high flow detection is disabled, then this event is logged immediately.
28	Encoder micro reset	The device has detected that the encoder micros has reset unexpectedly.
500	Critical error (internal)	A critical internal error not described by other events.
501	Rightsizing started	A rightsizing operation request for the ERT has been sent from the client.
502	Rightsizing completed	The rightsizing operation is complete.
503	Right sizing canceled.	A rightsizing operation cancelation request for the ERT has been sent from the client.
504	Flash error	A flash error has been detected.
505	Meter quiet mode exit	Occurs when the ERT gets pulses or detects consumption for the first time.
506	Entering OW Riva network mode	The device has been changed to OpenWay Riva network mode.
507	Set battery params	Any change to the BatteryUseParameters structure results in this event.
508	Set meter rightsizing params	The meter rightsizing parameters have been changed.
509	Key update	The key has been updated in the device.
511	Load profile cleared	The load profile object has been cleared.
512	Manual time sync	The time has been changed manually.
514	Legally relevant event log nearly full	This event occurs when the Legally Relevant log is at 90% of its total capacity.
515	Time sync - over threshold detected	A time change greater than the warning level threshold has been detected.
516	Time sync - over threshold end	A time change greater than the warning level threshold has ended and is back below the threshold.
517	Entering 100S mode	The device has been changed from OpenWay Riva network mode to 100S mode.
3000	Device reconfigured	The OpenWay Operations Center (OWCM) configuration in the device has changed.
3001	Event log cleared	The Itron event log has been reset.
3003	Configuration downloaded	A new configuration has been downloaded.
3004	System reboot	A watchdog error. Reboot.
3005	System restart	A planned restart of ERT (for example, after firmware download).
3006	Improper installation detected	The ERT could not adopt configuration information.
3015	Authentication failed	Application level security failure-authentication.
3016	Access control failed	An application level security failure - access control. This event occurs with an application level security failure for access control.
3017	Key rollover	A key rollover command received.
3018	Key signing	An application level security failure - certificate.
3019	Takeover package accepted	A takeover package was presented and accepted by the ERT.
3020	Takeover package rejected	A takeover package was presented, but rejected by the ERT.
3021	Replay attack detected	An application level security failure - replay.
3022	RMA signed authorization received	A signed authorization with issued-to "Itron-RMA" has been received.
10000	PCOMP changed	Metrology parameter (PCOMP) changed.
10001	Count rate changed	Metrology parameter (Count Rate) changed.
10002	Rollover count changed	Metrology parameter (Rollover Count) changed.
10006	Initial index	Metrology parameter (Initial Index) changed.
10007	Image transfer initiated (enabled)	An image transfer command was initiated.
10008	Image transfer canceled (disabled)	An image transfer command was canceled.
10009	Image transfer cancel failed	An image transfer command was canceled but was not successful.
10010	Image verification initiated	The process to verify an image has begun.
10011	Image verification successful	The image verification process was successful.
10012	Image verification failed	The image verification process was initiated, but was not successful.
10013	Image activation initiated	The image activation process was initiated.
10014	Image activation successful	The image activation process was successful.
10015	Image activation failed	The image activation process was initiated, but was not successful.
10019	Load profile interval changed	A change has been made to the CompressedLoadProfile object capture_period.

2

Register error

No communication with register.

4

Tilt detected

The tilt detector has been activated, like as a result of physical tampering.

5

Magnetic detected

The ERT has detected an external magnetic field.

6

Low battery

The ERT has a low battery warning. 10% of battery life remains.

16

Tilt debounce parameter changed

The tilt debounce parameter has changed.

20

High flow detected

The ERT detects consumption that exceeds the high flow threshold

21

High flow end

The ERT detects that consumption has dropped below the high flow threshold after being in a high flow state.

Note: If the ERT is in a high flow detected state and high flow detection is disabled, then this event is logged immediately.

28

Encoder micro reset

The device has detected that the encoder micros has reset unexpectedly.

500

Critical error (internal)

A critical internal error not described by other events.

501

Rightsizing started

A rightsizing operation request for the ERT has been sent from the client.

502

Rightsizing completed

The rightsizing operation is complete.

503

Right sizing canceled.

A rightsizing operation cancelation request for the ERT has been sent from the client.

504

Flash error

A flash error has been detected.

505

Meter quiet mode exit

Occurs when the ERT gets pulses or detects consumption for the first time.

506

Entering OW Riva network mode

The device has been changed to OpenWay Riva network mode.

507

Set battery params

Any change to the BatteryUseParameters structure results in this event.

508

Set meter rightsizing params

The meter rightsizing parameters have been changed.

509

Key update

The key has been updated in the device.

511

Load profile cleared

The load profile object has been cleared.

512

Manual time sync

The time has been changed manually.

514

Legally relevant event log nearly full

This event occurs when the Legally Relevant log is at 90% of its total capacity.

515

Time sync - over threshold detected

A time change greater than the warning level threshold has been detected.

516

Time sync - over threshold end

A time change greater than the warning level threshold has ended and is back below the threshold.

517

Entering 100S mode

The device has been changed from OpenWay Riva network mode to 100S mode.

3000

Device reconfigured

The OpenWay Operations Center (OWCM) configuration in the device has changed.

3001

Event log cleared

The Itron event log has been reset.

3003

Configuration downloaded

A new configuration has been downloaded.

3004

System reboot

A watchdog error. Reboot.

3005

System restart

A planned restart of ERT (for example, after firmware download).

3006

Improper installation detected

The ERT could not adopt configuration information.

3015

Authentication failed

Application level security failure-authentication.

3016

Access control failed

An application level security failure - access control.

This event occurs with an application level security failure for access control.

3017

Key rollover

A key rollover command received.

3018

Key signing

An application level security failure - certificate.

3019

Takeover package accepted

A takeover package was presented and accepted by the ERT.

3020

Takeover package rejected

A takeover package was presented, but rejected by the ERT.

3021

Replay attack detected

An application level security failure - replay.

3022

RMA signed authorization received

A signed authorization with issued-to "Itron-RMA" has been received.

10000

PCOMP changed

Metrology parameter (PCOMP) changed.

10001

Count rate changed

Metrology parameter (Count Rate) changed.

10002

Rollover count changed

Metrology parameter (Rollover Count) changed.

10006

Initial index

Metrology parameter (Initial Index) changed.

10007

Image transfer initiated (enabled)

An image transfer command was initiated.

10008

Image transfer canceled (disabled)

An image transfer command was canceled.

10009

Image transfer cancel failed

An image transfer command was canceled but was not successful.

10010

Image verification initiated

The process to verify an image has begun.

10011

Image verification successful

The image verification process was successful.

10012

Image verification failed

The image verification process was initiated, but was not successful.

10013

Image activation initiated

The image activation process was initiated.

10014

Image activation successful

The image activation process was successful.

10015

Image activation failed

The image activation process was initiated, but was not successful.

10019

Load profile interval changed

A change has been made to the CompressedLoadProfile object capture_period.